How to Build a St. Andrew’s Cross

DIY: Build a St. Andrews Cross: You don’t need to be a master craftsman to create a simple St. Andrew’s cross for your dungeon. If you are familiar with a simple ‘angled cross lap’ joint you will likely understand the concept behind creating a cross of this nature. A cross lap joint is created by cutting out a fraction of the middle part of a plank of wood to 55 degrees (or thereabouts), then, mirroring the joint on an opposing plank in order to marry the two together and create an ‘X’.

Getting started is easy but you will need sufficient space to work in so that you are not cramped, and you can turn the planks around without hitting one of your ornaments or fittings. Make sure the room is well ventilated, also, so that you don’t get saw dust everywhere (or do it outside).

 

BDSM: Spanking on the St. Andrews Cross
Photo Credit: SpankingGifs.com

Materials Needed:

2 6”x 2”x 80” planks of treated hard wood

2 4” x 2” x 60” planks of treated wood

1 3/8″ x 8″ carriage bolt

10 4” metal hooks/clips (Heavy duty)

4 2” screw in wall anchors

4 3/8 4” Wood screws

 

Tools Needed:

Screw driver

Drill

3/8″ drill bit

Measuring tape

Spirit level

Carpenter pencil

Tenon saw

Chisel

Countersink drill bit

Sand paper (120)

Protractor

 

Prior to building, sand down all the wood and lightly paint/varnish it in the color of your choice.

DIY Plans to Build a St. Andrew’s Cross

Step 1:

Measure a spot on the wall at 90” high and mark a horizontal level line. Use the level to mark the length of the 60” planks and draw a line above where they will be fixed. Repeat process for the lower plank and mark the line at 2 feet from the ground.

Step 2:

Drill holes for the wall anchors 4 inches from either end of the planks. Make sure they are level. Screw in the wall anchors until tight.

Step 3:

Secure the top and bottom planks into place with screws. Your two bars should now be 78 inches apart and parallel to one another.

Step 4:

To make the St. Andrew’s Cross place on plank flat down and mark a 55 degree angle with the protractor. Mark a point half way through the wood so that you are cutting out exactly the amount you are leaving there (for a 2 inch thick plank, cut 1 inch deep). Using the Tenon saw, cut from one marked line to the opposite bottom corner of the other line. Cutting from one corner to the other is easier because you leave a smaller chunk to chisel out. Once you have cut across both lines you will be left with a small triangle shaped heap which you can then chisel out until the cut out is flat.

Step 5:

Repeat step on other plank so that the two marry together.

Step 6:

Mark the center point and drill a hole for the carriage bolt. Spear it through and tighten the nut.

Step 7:

Place the Cross portrait style against the middle of the two parallel bars and drill holes through where all points meet. Secure with wood screws.

Step 8: Secure the hooks/clips in strategic places for the ankles and wrists.

Your St. Andrew’s cross is now ready for its first subject. You can also add your own accessories, such as spreader bars, hand cuffs, ankle cuffs and such, to get a more professional look.


Video: The St. Andrews Cross at London Dungeon Hire

6 thoughts on “Build a St. Andrews Cross”

  1. Thanks for the DIY St. Andrews Cross plans. I am building my St. Andrews Cross and wanted to ask if there is any particular wood you recommend for best performance.

    Reply
    • Walnut or maple are perhaps the best wood for building a St. Andrews Cross. Mahogany, birch, oak or cherry would also be good choices. You might even get by with pine, which is lighter weight, for your St. Andrews Cross construction, but I prefer the heavier woods. Thanks for the question GlennK31. We’d love to see a photo of your finished work!
      xoxo DOMinique

      Reply
  2. What angles would you cut the boards at on the ends so they sit flat on the ground?

    Reply
    • Place it up against a wall, at the angle of your choice, take any narrow book, place the book on the ground flat at the foot of your project, scribe a line level with the book on the wood. That will give you the angle you need for the footing

      Reply
  3. Hello question when making the lap joint where the 2 boards overlap do you place it in the half way points on both boards so the boards are even thanks

    Reply

Leave a Reply to Dimitri Cancel reply